Navigation

  • .30VG(P) ES ABL 21E Slide Carburetor

    By O. S. Engines |
    Product Number OSMG2078
    $0.00

    y Please allow 5-7 days for free in store pick up or flat rate shipping.
    1/10 Desert Truck Rtr
    To browse selection and pricing, enter your Zip Code below then click SHOP THIS HOBBYTOWN.
    X
    HobbyTown USA locations within miles of
    qty $0.00

    This is the O.S. Max 30VG (P) ES Electric Start, Rear Exhaust Monster Truck Engine with Pilot Type Crankshaft. Needle Settings: High Speed: 2 3/4 turns out from...*More

    This is the O.S. Max 30VG (P) ES Electric Start, Rear Exhaust Monster Truck Engine with Pilot Type Crankshaft. Needle Settings: High Speed: 2 3/4 turns out from fully closed Metering Needle (low speed): flush with ball link body, then 1.5 turns in Throttle Stop Screw: 1/2mm open from fully closed COMMENTS: The manual says to install the backplate from the HPI Roto Starter System onto the engine. This is incorrect, the compatible backplate is already installed on the engine. The backplate for the HPI K4.6 engine will not fit on this engine. To use this engine on the Duratrax Nitro Warhead, use OFNG0098 Clutch Nut. jxs 11/13/06 ir/jxs updt lmm 4/14/09*Less

    Rating:
    Print This Page
    Key FeaturesFull SpecsNeeded to Complete Comments/Reviews
    • Advanced Bi-Metallic Liner (ABL) cylinder liner construction
    • Also, the plating process is more consistent, resulting in a more precise fit between piston and sleeve for better compression and longer life.
    • Kwik-Pit Super Start for the HPI Savage or the HPI
    • Machined aluminum piston, 3-port cylinder liner and double bushed knife edge connecting rod 21E single needle Slide Valve Carburetor (OSMG2456) with insulated sleeve to prevent fuel vaporization SG (pilot) type oversized crankshaft with rubber-sealed front bearing and oversized rear bearing to handle high torque loads
    • Preinstalled E.S.
    • Roto Starter System (HPIP8711), see COMMENTS
    • Same mounting dimensions as .21 size engines making upgrading easier
    • Starter backplate is designed to use the DuraTrax
    • This helps the metal bond to the cylinder and ismore durable.
    • This process uses a double layer of plating material rather thanone thick layer.
    • Bore:0.728 (18.5mm)
    • Crankshaft Size:1/4-28
    • Displacement:0.298 cu in (5.0cc)
    • Distance Between Mounting Holes Diagonal:2.3 (59mm)
    • Distance Between Mounting Holes Opposite Side:1.4 (37mm)
    • Distance Between Mounting Holes Same Side:0.83 (21mm)
    • Distance from Center of Engine to Backplate:1.4 (35.6mm)
    • Distance from Center of Engine to Front Bearing:1.7 (44mm)
    • Distance from Front Bearing to end of Crankshaft:1.2 (29.5mm)
    • Factory Needle Valve Setting:2-3/4 turns OPEN from fully closed
    • Mixture Control Valve Setting:Needle head flush with the side of
    • Power Output:3.0 PS, 2.96 HP/28, 000 RPM
    • Practical RPM:4, 000-36, 000
    • Stroke:0.717 (18.2mm)
    • Weight:12.7oz (360g)
    • Width of Crankcase Below Mounting Ears:1.2 (30.8mm)
    • Width of Mounting Tabs:1.8 (45mm)
    • ~Coming Soon
  • To browse selection and pricing, enter your Zip Code below then click SHOP THIS HOBBYTOWN.
    X
    HobbyTown USA locations within miles of